How To Install Access Panel In Drywall Ceiling

Download Commodity

Download Article

Installing ceiling drywall is a very unproblematic process, but can be slightly challenging when working solitary. Past making a few pocket-sized adjustments, nigh anyone can accomplish this job on their ain. If you make the right preparations and install your drywall in the correct procedure, you should have no problem installing drywall on your ceiling.

1. 1

   Inspect the ceiling for obstructions or issues that demand to be fixed. Before y'all install the drywall, bank check to make sure electrical wires, ductwork, protruding pipes, and other obstructions won't be in your fashion. As well, take this opportunity to make certain there aren't any obvious problems, such equally faulty plumbing, that would be easier to address without drywall in the way.^[1]

   • Install furring strips to the framing in order to create a flat, even surface for drywall installation effectually these obstacles as necessary.

2. ii

   Find the ceiling joists and marking their location on the wall. You'll demand to know where the ceiling joists are located at all times during this process. If you can't encounter the joists, tap on the ceiling with a hammer and listen for a solid audio indicating forest framing.^[two]

   • Y'all can only use a pencil to mark the locations on the wall.

   Advertising

3. 3

   Mark the placement of low-cal fixtures and vents on the drywall. Notation where the different lite fixtures, vents, and electrical boxes are located on the wall and mark their locations on the drywall yous plan to identify on tiptop of them. You lot'll demand to look until afterward the drywall is attached to the ceiling earlier cutting holes in it for these fixtures.^[3]

   • You might also precisely mark these locations on a plan of the ceiling, noting their exact distance from the walls.

4. 4

   Smoothen the rough edges of the drywall pieces. Smoothing the crude edges on the cut edges of your drywall pieces volition ensure tight joints betwixt the drywall. Use a surform tool to sand downward the edges of the drywall until they're smooth.^[4]

5. five

   Build a T-caryatid if you'll be working alone or without a elevator. A T-brace will provide the leverage and support needed to heighten the drywall panels to the ceiling when you lot're working lone. Use a two feet (61 cm) piece of 1x4 and nail it to a 2x4 that is long enough to be 1 foot (thirty cm) higher than the length from the floor to the ceiling.^[v]

   • A T-caryatid isn't necessary if you lot're using a drywall lift, which is a machine that smoothly lifts drywall to the ceiling so you don't have to lift information technology. Drywall lifts tin be cheaply rented from department stores and most stores that sell construction equipment.

   Advertisement

1. 1

   Utilize adhesive to the joists where the first sheet of drywall will go. Start in the corning and heighten the first canvass of drywall to the ceiling so you tin can get an idea of the placement across the joists. Look until yous know where you lot're placing the sheet before you apply any adhesive to the joists.^[6]

   • Drywall adhesive dries within 15 minutes, so brand certain you're ready to begin placing the drywall every bit soon every bit you utilize the adhesive.

2. two

   Raise the first piece of drywall to the ceiling. Using your T-brace, or a friend to assist you, enhance the get-go sheet of drywall to the ceiling and slide information technology snugly into the corner. Make certain that the tapered edges of the sheet are facing the floor.^[seven]

   • If y'all're using a drywall lift, motility the lift underneath the ceiling and place the drywall sheet on the lift and so that information technology is directly under the corner of the ceiling. Lift it slowly, making sure the sheet doesn't jostle or motility out of position.

3. three

   Repeat this procedure along the first wall. Adhere the next piece of drywall using this same process and keep along the wall, always ensuring that the tapered edges abut one some other and are facing downwards.

   • The tapered edges are designed to brand the process of taping and mudding easier, then it'due south important that they remain facing downward.

4. 4

   Affix the drywall sheets permanently to the ceiling joists. Utilize either nails or screws to adhere the drywall to the joists. Bulldoze the fasteners in .375 inches (0.95 cm) away from the edges of each sheet and space them seven inches (xviii cm) autonomously along the perimeter. Along the interior joist, install the fasteners at well-nigh 12 inches (30 cm) increments.^[8]

   • The heads of the fasteners you choose should come in contact with the paper facing, sinking in slightly without breaking through the paper.

5. 5

   Start the second row with a half sheet of drywall to stagger the seams. When y'all finish the first row of drywall and move on to the second, make sure the seams don't line up between the ii rows. Having staggered seams will enforce the stability of the drywall.^[ix]

   • Measure and marker the cut line at the vertical midpoint of the drywall sheet and utilize a utility pocketknife to cut through the drywall. Tip the panel off of the floor or tabular array at a slight angle, then push it downwardly to break information technology in half.
   • Use the aforementioned process to attach this half-piece of drywall as you used on the first row of drywall.

6. six

   Repeat this process until the entire ceiling is covered. Continue to identify drywall in rows along the ceiling, affixing them in place with nails or screws. Equally you move from one row to the next, make sure to stagger the seams to ensure the drywall's stability.

7. vii

   Go dorsum and cut holes in the drywall for vents and fixtures. Now that the drywall is set, go back and cut holes in the places you marked for vents, lights, and electrical boxes. Utilise a spiral cutout saw to make the cutting process quick and piece of cake.^[ten]

   Advertisement

Add New Question

• Question

  Can I sheetrock a ceiling myself?

  

  Agustin Renoj is a Home Improvement Specialist with Renoj Handyman based in the San Francisco Bay Surface area. With over 18 years of structure feel, Agustin specializes in carpentry, painting, and exterior, interior, kitchen, and bath renovations. Renoj Handyman is a family-owned business that consists of craftsmen trained in all areas of construction.

  

  Home Improvement Specialist

  Skilful Reply

  The all-time matter to practice is to hire someone who does that for a living—it volition become finished much faster and will usually look much nicer. If you do decide to exercise it yourself, yous're going to need at to the lowest degree two people to help you, considering sheetrock is very heavy and you can easily go injure.

• Question

  How do I repair a ceiling where a portion is falling in and needs to be replaced?

  

  Mark off a squared or rectangular-shaped line around the damaged area. Determine the orientation and location of the ceiling joists. Extend your squared off markings so that two opposite sides of the outline fall on center, directly over the ceiling joists. Cut out the box shape, and install new drywall into the expanse. Fasten forth the edges falling over the joists. Besides, make sure all of the damaged drywall is removed and that the problem that caused it is likewise repaired. Finally, stop as you would a regular drywall installation.

• Question

  How practice I drywall a ceiling that needs insulation?

  

  Install friction fit batts, sized to see the lawmaking requirements in your area; cover the area completely with six mil poly, taping all joints; then fasten upward the drywall.

• Question

  What size sheet rock is needed for a ceiling?

  

  One-half-inch is standard, but your area's building lawmaking may require a dissimilar size, so check your area's building code.

• Question

  How do I attach drywall to a metal air vent?

  

  You don't. Drywall should non be in directly contact with the heating duct. As the duct warms when hot air goes through it, the expansion of the duct will create an annoying noise, break loose the screws, or both. You need to frame beneath the duct to fasten the drywall to either woods or metal framing that is not attached to the duct.

• Question

  How do I board out a ceiling that is gear up for plaster board on a non-standard construction firm?

  

  You can rent or buy a support tool specifically designed for this purpose. Mensurate, cutting, so lay information technology on the support tool. It is adjustable and can hold the drywall at the proper meridian. Screw the drywall to the ceiling joists.

• Question

  What's the standard meridian of ceiling from floor?

  

  Standard ceiling heights are finished out at roughly eight ft. precisely with i sole plate (bottom) and two top plates, and an unfinished wall volition stand at 97 1/eight". Your tiptop could vary slightly based on imperfections in materials or the thickness of the drywall used. Any uncovered wall should exist at the bottom of the wall, and should ultimately be covered by trim/base moulding. This is usually no more 1/2" to 7/viii". Always push button the top of your sheeting tight and leave the gap at the bottom if there is one.

• Question

  I'chiliad trying to stop the basement ceiling because our contractor backed out later on doing the walls first, so how exercise I make sure everything looks okay when walls are done but the ceiling isn't?

  

  THOMAS COURTNEY

  Community Answer

  Nigh people believe that ceilings must be done starting time, but this isn't true. Doing a ceiling first only helps to hide edges and off cuts. Make sure that the wall lath is completely screwed at the top . This volition aid to go on things straight. Yous have two option then. Y'all can mensurate a middle point to the middle of the ceiling, placing your canvas dead heart of the line, though this isn't recommended if you're not a professional. It's easier to start from a directly corner placing a full sheet in opposite direction of the studs. Your 2d canvass should be at to the lowest degree 2 - iv feet shorter than the get-go one. Identify it on the 2d row. Complete your first row, so continue on until you're finished.

• Question

  What should the thickness of the drywall on the ceilings exist?

  

  1/2 in is standard, but the code in your area may require a different size, so check your surface area'south building code to be certain.

• Question

  How far should the screws go into the ceiling joists when installing a drywall ceiling over an existing one?

  

  To the point where the head contacts the drywall, too far and you could harm the drywall.

Show more answers

Ask a Question

200 characters left

Include your email accost to go a message when this question is answered.

Submit

Advertisement

Video

• Keep the drywall sheets laid out flat on the flooring until you're gear up to utilize them. This will prevent them from bending.

• Professionals rarely use gum on ceiling joists, partly considering of the greater likelihood of ceiling boards needing to be taken downwards and trimmed. Instead of gluing, we generally use iii coarse thread drywall screws(or three sets of 2 nails) in the "field" in add-on to the screw on each edge of the board.

• The joists should be marked on the acme "plate," the plate is typically made of two 2x4s on tiptop of the studs.

• Longer does not hateful better in the choice of screw length. A 2" spiral volition not agree a one/2" piece of drywall any better than a one and one quarter inch spiral, simply it will exist very much more hard to start and to screw in straight.

• For the 10 to 15 dollar cost, a drywall T square volition pay for itself in a hurry! Lean the sheet almost upright confronting the wall and use the toe of your left foot(if you are right-handed) to concur the bottom of the square. Score the sheet on your mark. And so pick it upwards just slightly off the floor and snap the sheet. Lean over the canvass and cut through the newspaper for a foot or two nearly the heart of the cut. Grasp the end that is to come off, and with a quick move, push your end of the whole canvas away from yous and snap the finish off! For quickly mark openings for lights, outlets, etc a square is indispensable.

• Drywall is available in a variety of thicknesses. The recommended thickness is ⁵⁄_viii inch (1.vi cm) for ceiling installation. Special 1/two in ceiling lath is also available. If the installation is to be inspected, the inspector can tell you what is acceptable.

Advertisement

• Make certain you wear eye protection!

Advertizement

Near This Article

Article Summary X

To install ceiling drywall, start past applying adhesive to the joists where the first sheet of drywall will go. Next, raise the drywall up with the help of a friend or drywall elevator. Once the starting time piece is in place, repeat the process forth the start wall, making sure the tapered edges face downwardly. After the drywall sheets are up, boom or screw them into the joists to affix them permanently. When you start the second row, brand sure to stagger the seams to enforce the stability of the drywall. Finally, cutting holes in the drywall for vents and fixtures. To acquire how to build a T-brace to enhance the drywall panels to the ceiling when working alone, keep reading!

Did this summary aid y'all?

Thanks to all authors for creating a folio that has been read 542,346 times.

Did this article assist you?

Source: https://www.wikihow.com/Install-Ceiling-Drywall

Posted by: jesterthemply.blogspot.com

Share this post